Note AcademyNote Academy

Chemistry YCH11 · Chapter 11

Volumetric analysis

Acid-base titrations and indicators, preparing a standard solution, titration calculations, and measurement uncertainty.

5 min read

Download this chapter (PDF)

Acid–base titration

In a titration, a solution of known concentration (usually in the burette) is added to a measured volume of another (in a conical flask) until the end point, shown by an indicator, is reached.

Steps for a calculation:

  1. Write the balanced equation.
  2. Find the moles of the solution whose volume and concentration are known: n=c×Vn = c \times V (with VV in dm3^3).
  3. Use the mole ratio to find the moles of the other reactant.
  4. Find the concentration: c=n/Vc = n / V.
  5. If needed, convert to g dm−3^{-3} by multiplying by the molar mass.

NaOH+HCl→NaCl+H2ONaOH + HCl \rightarrow NaCl + H_2O. n(HCl)=0.100×0.02140=2.14×10−3n(HCl) = 0.100 \times 0.02140 = 2.14 \times 10^{-3} mol. The ratio is 1 : 1, so n(NaOH)=2.14×10−3n(NaOH) = 2.14 \times 10^{-3} mol in 25.0 cm3^3. c=2.14×10−3/0.0250=0.0856c = 2.14 \times 10^{-3}/0.0250 = 0.0856 mol dm−3^{-3}.

Indicators

IndicatorColour in acidColour in alkaliUse
Methyl orangeRedYellowStrong acid with weak base
PhenolphthaleinColourlessPinkStrong base with weak acid

For strong acid with strong base either works. Use a few drops only, because the indicator is itself a weak acid and changes the result if too much is added.

Core Practical 3: concentration of hydrochloric acid

  1. Fill a clean burette with the standard solution (rinsing first with the solution), and remove any air bubbles in the tip.
  2. Use a pipette to transfer 25.0 cm3^3 of the other solution to a conical flask and add the indicator.
  3. Run in the solution slowly with swirling. Do one rough titration, then repeat accurately, adding drop by drop near the end point.
  4. Repeat until concordant results (within 0.10 cm3^3) are obtained, and use their mean.

Core Practical 4: a standard solution

A standard solution has an accurately known concentration. To prepare it from a solid acid:

  1. Weigh the solid accurately by difference: record the mass of a weighing bottle, add the solid, record again, then tip the solid into a beaker and reweigh the bottle.
  2. Dissolve it in a little deionised water in a beaker, stirring.
  3. Pour it into a volumetric flask through a funnel, rinsing the beaker and funnel into the flask.
  4. Make up to the mark with deionised water (the bottom of the meniscus on the line), stopper and invert to mix.

The solution is then used to find the concentration of sodium hydroxide, as in the titration above.

A primary standard is stable, pure, has a high molar mass and is not hygroscopic. Hydrated ethanedioic acid and anhydrous sodium carbonate are used.

Water of crystallisation and other calculations

Titration data can be used to find the MrM_r of an acid, the percentage purity of a sample, the concentration in g dm−3^{-3} of a solution, or the number of moles of water of crystallisation, xx, in a hydrated salt.

Na2CO3+2HCl→2NaCl+H2O+CO2Na_2CO_3 + 2HCl \rightarrow 2NaCl + H_2O + CO_2. n(HCl)=2.00×10−3n(HCl) = 2.00 \times 10^{-3} mol, so n(Na2CO3)=1.00×10−3n(Na_2CO_3) = 1.00 \times 10^{-3} mol in 25.0 cm3^3, so 1.00×10−21.00 \times 10^{-2} mol in 250 cm3^3. M=1.43/0.0100=143M = 1.43/0.0100 = 143. x=(143−106)/18=2x = (143 - 106)/18 = 2.

Uncertainty

Each piece of apparatus has an uncertainty. The percentage uncertainty is

uncertaintymeasurement×100\frac{\text{uncertainty}}{\text{measurement}} \times 100

  • A burette reading has an uncertainty of ±0.05 cm3^3, and a titre is the difference between two readings, so its uncertainty is ±0.10 cm3^3.
  • A 25.0 cm3^3 pipette typically has ±0.06 cm3^3.
  • A balance reading to 0.001 g has ±0.0005 g for each reading.

For the final result, add the percentage uncertainties of all measurements in a calculation. To reduce the uncertainty:

  • use a larger titre (a more dilute solution, or a larger mass of solid) so that the fixed error is a smaller percentage,
  • use a balance of higher resolution,
  • make a stock solution and use a larger volume.
Test yourself10 flashcards on this chapter.Flashcards →

These notes are AI generated and may contain mistakes. Check them against your syllabus.