Note AcademyNote Academy

Chemistry YCH11 · Chapter 6

Energetics

Enthalpy changes and their standard definitions, enthalpy level diagrams, calorimetry, Hess's law cycles, and bond enthalpies.

6 min read

Download this chapter (PDF)

Enthalpy change

The enthalpy change, ΔH\Delta H, is the heat energy change measured at constant pressure. By convention:

  • exothermic reactions release heat to the surroundings: ΔH\Delta H is negative, and the temperature of the surroundings rises.
  • endothermic reactions take in heat: ΔH\Delta H is positive, and the temperature of the surroundings falls.

Standard conditions are a pressure of 100 kPa and a stated temperature, usually 298 K, with each substance in its standard state. The symbol ΔH⊖\Delta H^{\ominus} is used.

Enthalpy level diagrams

An enthalpy level diagram has enthalpy on the vertical axis. For an exothermic reaction the products are lower than the reactants and ΔH\Delta H is shown as a downward arrow; for an endothermic reaction the products are higher and the arrow is upward.

Standard enthalpy changes

NameSymbolDefinition (all under standard conditions)
ReactionΔrH\Delta_r HThe enthalpy change when the amounts of reactants in the equation react to give the products
FormationΔfH\Delta_f HThe enthalpy change when one mole of a compound forms from its elements in their standard states
CombustionΔcH\Delta_c HThe enthalpy change when one mole of a substance burns completely in oxygen
NeutralisationΔneutH\Delta_{neut} HThe enthalpy change when an acid and an alkali react to form one mole of water
AtomisationΔatH\Delta_{at} HThe enthalpy change when one mole of gaseous atoms forms from the element in its standard state

Measuring enthalpy changes

The energy transferred to a known mass of water or solution is

q=mcΔTq = mc\Delta T

where qq is in J, mm is the mass of solution in g, cc is the specific heat capacity (4.18 J g−1^{-1} °C−1^{-1} for water) and ΔT\Delta T is the temperature change in °C.

ΔH=−qn (in kJ mol−1, with q in kJ)\Delta H = -\frac{q}{n} \ (\text{in kJ mol}^{-1}, \text{ with } q \text{ in kJ})

q=100×4.18×6.8=2842q = 100 \times 4.18 \times 6.8 = 2842 J. Moles of water =0.0500= 0.0500. ΔH=−2.842/0.0500=−56.8\Delta H = -2.842/0.0500 = -56.8 kJ mol−1^{-1}.

Experiment types

  • Solutions in an insulated container (polystyrene cup with a lid): mix reagents and record the temperature over time.
  • Combustion (spirit burner and a copper calorimeter): burn a fuel to heat a known mass of water.

Evaluating the experiment

Sources of error are heat lost to the surroundings (the main one), incomplete combustion, heat absorbed by the container, evaporation of fuel, and the use of a thermometer with limited resolution. Improve by insulating and using a lid, stirring, and using a draught shield. For solutions, plot temperature against time, then extrapolate the cooling line back to the time of mixing to estimate the maximum temperature rise that would have occurred with no heat loss (a cooling curve correction).

Hess's law

Hess's law states that the total enthalpy change for a reaction is independent of the route taken, provided the initial and final conditions are the same. It is a consequence of the conservation of energy.

Using enthalpy of formation

ΔrH=∑ΔfH(products)−∑ΔfH(reactants)\Delta_r H = \sum \Delta_f H(\text{products}) - \sum \Delta_f H(\text{reactants})

Using enthalpy of combustion

ΔrH=∑ΔcH(reactants)−∑ΔcH(products)\Delta_r H = \sum \Delta_c H(\text{reactants}) - \sum \Delta_c H(\text{products})

ΔrH=(−235)−(+52+−242)=−235+190=−45\Delta_r H = (-235) - (+52 + -242) = -235 + 190 = -45 kJ mol−1^{-1}.

Draw the cycle with arrows: elements at the bottom, reactants and products above. Follow the direction of the arrow when adding and reverse the sign if you go against it.

Bond enthalpy

The bond enthalpy is the enthalpy change when one mole of a covalent bond is broken in the gas phase. It is always endothermic. The mean bond enthalpy is the average value over a range of compounds with the same bond (for example C–H in different molecules).

ΔrH=∑(bonds broken)−∑(bonds made)\Delta_r H = \sum (\text{bonds broken}) - \sum (\text{bonds made})

Bonds broken: 4(413)+2(497)=26464(413) + 2(497) = 2646. Bonds made: 2(805)+4(464)=34662(805) + 4(464) = 3466. ΔH=2646−3466=−820\Delta H = 2646 - 3466 = -820 kJ mol−1^{-1}.

Mean bond enthalpies can be found from a known ΔrH\Delta_r H and the other bond enthalpies.

Limitations

Mean values differ from the actual bond enthalpy in a specific molecule, and the method only applies to gaseous species. Answers from bond enthalpies are less accurate than those from formation data.

Bond enthalpy also gives an indication of which bond breaks first and how fast a reaction proceeds. A weaker bond breaks more easily, which is why the C–I bond in iodoalkanes reacts faster than the C–Cl bond in chloroalkanes.

Test yourself10 flashcards on this chapter.Flashcards →

Practise this chapter

Every past-paper question on these topics, with the mark scheme.

These notes are AI generated and may contain mistakes. Check them against your syllabus.