Note AcademyNote Academy

Chemistry YCH11 · Chapter 13

Halogenoalkanes

Nucleophiles, naming and classifying halogenoalkanes, their reactions with a range of reagents, nucleophilic substitution mechanisms, rates of hydrolysis, and how they are made.

5 min read

Download this chapter (PDF)

Nucleophiles and polar bonds

A nucleophile is an electron-pair donor: it attacks a δ+\delta+ atom using a lone pair. Examples are OH−OH^-, CN−CN^- and NH3NH_3.

Reaction mechanisms depend on bond polarity. The C–X bond in a halogenoalkane is polar, because halogens are more electronegative than carbon (Cδ+−Xδ−C^{\delta+}-X^{\delta-}), so the carbon is attacked by nucleophiles.

Halogenoalkanes have the general formula CnH2n+1XC_nH_{2n+1}X. They are named with a prefix: chloro-, bromo-, iodo-, e.g. 1-bromobutane, 2-chloro-2-methylpropane.

  • Primary: the carbon bonded to the halogen is attached to one other carbon (e.g. 1-bromopropane).
  • Secondary: attached to two other carbons (2-bromopropane).
  • Tertiary: attached to three other carbons (2-bromo-2-methylpropane).

Reactions of halogenoalkanes

ReagentConditionsProductRole of reagent
Aqueous KOH or NaOHWarm, refluxAlcoholOH−OH^- is a nucleophile: substitution (hydrolysis)
Ethanolic KOHHot, refluxAlkeneOH−OH^- is a base: elimination
Aqueous silver nitrate in ethanolWarmHalide precipitate and alcoholH2OH_2O is the nucleophile; used to measure rates
Ammonia in ethanol (excess)Heat under pressure in a sealed tubePrimary amineNH3NH_3 is a nucleophile
Potassium cyanide in ethanol (alcoholic KCN)RefluxNitrileCN−CN^- is a nucleophile

The choice of solvent controls substitution or elimination: aqueous gives substitution, ethanolic gives elimination.

Mechanism: nucleophilic substitution (primary halogenoalkanes)

With hydroxide ions (shown for bromoethane):

  1. The OH−OH^- ion uses a lone pair to attack the δ+\delta+ carbon (curly arrow from the lone pair to carbon).
  2. At the same time the C–Br bond breaks heterolytically (curly arrow from the bond to Br) and Br−Br^- leaves.

It takes place in one step, through a transition state in which the carbon is partly bonded to both OHOH and BrBr.

With ammonia the first step gives CH3CH2NH3+Br−CH_3CH_2NH_3^+Br^-, and a second ammonia molecule removes an H+H^+ to give the amine, CH3CH2NH2CH_3CH_2NH_2.

Relative rates of hydrolysis

Add aqueous silver nitrate in ethanol to a halogenoalkane in a warm water bath. The halide ion formed gives a precipitate. The faster the precipitate appears, the faster the hydrolysis.

  • By structure: tertiary > secondary > primary.
  • By halogen: iodo > bromo > chloro. The rate depends on the C–X bond enthalpy: C–I is the weakest and breaks most easily, C–Cl is the strongest. (The polarity of the bond does not explain it, since C–Cl is the most polar.)

Precipitate colours: AgClAgCl white, AgBrAgBr cream, AgIAgI yellow.

The C–I bond is weaker than the C–Cl bond (lower bond enthalpy, because the iodine atom is larger and its bonding electrons are further from the nucleus), so it needs less energy to break and the rate is faster.

Core Practical 5 compares the rates of hydrolysis of a number of halogenoalkanes. Keep the volume, concentration, temperature and the amount of silver nitrate the same, and time the appearance of the precipitate.

Making a halogenoalkane: Core Practical 6

Tertiary alcohols react with concentrated hydrochloric acid at room temperature, so 2-chloro-2-methylpropane is made from 2-methylpropan-2-ol:

(CH3)3COH+HCl→(CH3)3CCl+H2O(CH_3)_3COH + HCl \rightarrow (CH_3)_3CCl + H_2O

The method:

  1. Shake the alcohol with concentrated HCl in a separating funnel, releasing the pressure often.
  2. Run off the lower aqueous layer and keep the upper organic layer.
  3. Wash with sodium hydrogencarbonate solution to remove the remaining acid (vent the funnel because CO2CO_2 forms).
  4. Dry with anhydrous sodium sulfate or calcium chloride.
  5. Distil, collecting the fraction at the boiling temperature of the product (51 °C).
Test yourself10 flashcards on this chapter.Flashcards →

These notes are AI generated and may contain mistakes. Check them against your syllabus.