Deducing a structure from data
Use all the evidence together.
- Combustion analysis or percentage composition gives the empirical formula.
- The molecular ion in the mass spectrum gives and the molecular formula.
- Chemical tests give functional groups: bromine water (C=C), 2,4-DNPH (C=O), Benedict's or Tollens' (aldehyde), iodoform (), sodium carbonate (COOH), (OH).
- Infrared confirms the groups (C=O near 1700, broad O–H).
- NMR gives the number of carbon environments and their types.
- Proton NMR gives the number of proton environments, their ratio, and (from splitting) neighbours.
The C=O at 1740 without O–H suggests an ester. A singlet at 2.0, an quartet next to a triplet: ethyl ethanoate, .
Increasing the length of the carbon chain
| Method | Reagents | Product |
|---|---|---|
| Nitrile route | Halogenoalkane with KCN in ethanol, reflux | Nitrile (+1 carbon); then hydrolyse (acid, reflux) to a carboxylic acid or reduce () to an amine |
| Hydroxynitrile | Aldehyde or ketone with HCN/KCN | Hydroxynitrile (+1 carbon) |
| Grignard reagent | Halogenoalkane with magnesium in dry ether | (a source of , a nucleophile) |
Grignard reagents
The reaction must be in dry (anhydrous) ether, because the Grignard reagent reacts with water to give an alkane, .
The reagent acts as a nucleophile (carbon with partial negative charge) towards carbons.
- With carbon dioxide, then dilute acid: a carboxylic acid (one more carbon):
- With aldehydes, then dilute acid: a secondary alcohol (methanal gives a primary alcohol)
- With ketones, then dilute acid: a tertiary alcohol
Planning a synthesis
Retrosynthesis: start with the target, ask what it can be made from, and work back. Combine the reactions in this specification (up to four steps).
Main functional-group conversions:
| From → To | Reagents |
|---|---|
| Alkane → halogenoalkane | or , UV |
| Alkene → halogenoalkane | HX |
| Alkene → alcohol | Steam, acid catalyst |
| Alkene → diol | Cold acidified |
| Halogenoalkane → alcohol | Aqueous NaOH, reflux |
| Halogenoalkane → alkene | Ethanolic NaOH |
| Halogenoalkane → nitrile | KCN in ethanol |
| Halogenoalkane → amine | Excess in ethanol, pressure |
| Alcohol → halogenoalkane | ; KBr + 50% ; red P and |
| Alcohol → alkene | Concentrated |
| Primary alcohol → aldehyde | , distil |
| Primary alcohol → carboxylic acid | , reflux |
| Secondary alcohol → ketone | |
| Aldehyde or ketone → alcohol | in dry ether |
| Aldehyde or ketone → hydroxynitrile | HCN, KCN |
| Carboxylic acid → ester | Alcohol, concentrated |
| Carboxylic acid → acyl chloride | |
| Acyl chloride → ester, amide | Alcohol; or an amine |
| Nitrile → carboxylic acid | Dilute acid, reflux |
| Nitrile → amine | in dry ether or |
| Benzene → nitrobenzene | Conc. + conc. |
| Nitrobenzene → phenylamine | Sn + conc. HCl, then NaOH |
| Phenylamine → diazonium salt | + HCl, below 5 °C |
In an exam you may also need to select a practical procedure, predict properties of unfamiliar compounds by recognising the functional groups, and identify control measures from hazard data.
Preparing and purifying an organic solid
| Technique | Purpose |
|---|---|
| Heating under reflux | Carry out the reaction without losing volatile reactants |
| Washing (with water or sodium carbonate solution) | Remove soluble impurities and acid, in a separating funnel |
| Solvent extraction | Separate the product into an organic solvent |
| Recrystallisation | Purify a solid |
| Drying (anhydrous salt for liquids; air or desiccator for solids) | Remove water |
| Distillation and steam distillation | Purify a liquid; steam distillation for a compound that is immiscible with water and would decompose at its own boiling temperature (e.g. limonene from orange peel) |
| Melting temperature determination | A pure solid melts at a sharp, specific temperature; impurities lower and broaden the melting range |
| Boiling temperature determination | Check purity of a liquid |
Recrystallisation
- Dissolve the impure solid in the minimum volume of hot solvent.
- Filter while hot (through a heated funnel) to remove insoluble impurities.
- Cool slowly. Pure crystals form and the soluble impurities stay in the solution because their concentration is low.
- Filter under reduced pressure (Buchner funnel), wash with a small volume of cold solvent, and dry.
Using too much solvent lowers the yield.
Core Practical 16: the preparation of aspirin
Aspirin (2-ethanoyloxybenzoic acid) is made by esterifying 2-hydroxybenzoic acid (salicylic acid) with ethanoic anhydride and a few drops of concentrated sulfuric (or phosphoric) acid as the catalyst.
- Warm the mixture in a water bath for about 15 minutes.
- Add cold water to destroy the excess ethanoic anhydride and precipitate the crude aspirin.
- Filter under reduced pressure and wash with cold water.
- Recrystallise from a minimum of hot ethanol or water.
- Dry the crystals, weigh them to find the percentage yield, and measure the melting temperature.
These notes are AI generated and may contain mistakes. Check them against your syllabus.

