Chemistry · May / June 2022 · Paper 31 · Question 1
YCH11
As printed in the paper
The question as text
1 An experiment is carried out to determine the enthalpy change for the reaction between zinc and copper(II) sulfate solution. Zn(s) + Cu2+(aq) → Zn2+(aq) + Cu(s) Procedure • weigh 4.50 g of zinc powder into a weighing bottle use a measuring cylinder to transfer 50.0 cm3 of 1.00 mol dm–3 • aqueous copper(II) sulfate into a polystyrene cup, held in a 250 cm3 beaker stir the solution with a thermometer, record the temperature to the nearest 0.5 °C • and start a timer • continue to stir the solution, recording the temperature every minute • at exactly 3.5 minutes, add the zinc powder to the aqueous copper(II) sulfate, stirring continuously • record the temperature of the solution every minute from 4.0 to 9.0 minutes. The results are shown. Time / min 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 Temperature / °C 21.5 22.5 22.0 22.0 60.5 63.0 60.5 58.5 57.0 55.5
Read automatically from the paper; the printed page above is exact.
Show the answer and mark scheme
1(a)(i)[1]
Example of graph
70.0
All ten points plotted65.0
accurately to within half a
square
60.0
55.0
50.0
45.0
40.0
35.0
30.0
25.0
20.0
15.0
10.0
5.0
0.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Ignore in this item extension of lines beyond the points or any additional
lines (e.g. linking the two lines together)
1(a)(ii)[3]
Example of graph
70.0
65.0
straight line of best fitlinking the top points
60.0
55.0
use of 3.5 minutes to find50.0
ΔT
45.0
value of ΔT correct from40.0
values on a vertical line
35.0
shown on the graph
ΔT = 66 – 22 = 44(ºC)
30.0
25.0
20.0
15.0
10.0
5.0
0.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0 10.0
Allow a best fit line through points at 6, 7 and 8 or through 8, 9 and 10 and
anything in between. (6, 7 and 8 gives 67 ºC, 8, 9 and 10 gives 63.5 ºC)
Ignore additional lines linking the two lines of best fit other than a vertical
line showing where the temperature change is being read.
1(a)(iii)[1]
An answer that makes reference to the following points:
the reaction is not instantaneous so the best fit lineAllow just deals with the effect of cooling
Allow just reaction is not instantaneous
allows for the effect of cooling (during the
reaction)
Allow takes account of heat loss
OR
Allow multiple measurements give a trend of
initial line takes into account changes in
temperature of the solution prior to reaction
temperature change (over time)
Ignore gives a calculation of more accurate final
temperature / temperature change
Ignore just gives a more accurate / better result
Ignore anomaly / anomalous
1(b)(i)[2]
Example of calculation
calculation of moles of zinc= 4.5 = 0.068807 / 0.0688 / 6.8807 × 10−2 / 6.88 × 10−2 / 0.07 (mol)
65.4
= 50 × 1.0 = 0.0500 / 5.0 × 10−2 (mol)
calculation of moles of1000
copper(II) sulfate (so zinc is in
excess)
Allow calculations finding required mass of zinc or volume of
copper(II) sulfate to match the number of moles of the other substances
and showing zinc is therefore in excess
Allow use of 65 for Ar of Zn
Ignore any justification of excess
Ignore SF
Correct answers with no working score (2)
1(b)(ii)[1]
Example of calculation
calculation of energy= 50 × 4.2 × ΔT (from (a)(ii))
transferred
= 50 × 4.2 × 44 = 9240 / 9.24 x 103 (J)
Allow 9.24 kJ but units must be given
Allow use of 4.18 for 4.2
Allow TE on answer to (a)(ii)
Do not award answers using 54.5/4.5 in place of 50
Do not award incorrect units e.g kJ mol‒1
Ignore sign
Ignore SF except 1 SF
Correct answer with no working scores (1)
1(b)(iii)[1]
An answer that makes reference to one of the following
points
Allow the metal / thermometer does not absorb heat
heat capacity of the metal / zinc / copper /energy
polystyrene cup can be ignored / is zero
Allow the mass of the metal can be ignored
Or
Allow use of specific heat capacity
Allow 1g = 1cm3
the density of the solution is 1 g cm‒3 / the same asIgnore the mass of solution is the same as the mass
water
of water
Ignore no heat loss
Do not award just density = 1 (with no unit)
1(b)(iv)[2]
Example of calculation
Allow TE on (b)(i) and (b)(ii) and at each stage
calculation of value for= answer to (b)(ii)
energy transferred per mole
moles of copper(II) sulfate from (b)(i)
= 9240 = 184800 / 185000 (J mol‒1)
0.0500
= ‒184800 = ‒184.8 / 185 (kJ mol‒1)
calculation of enthalpy change1000
including sign
Allow answer in J mol1 if unit given
Ignore SF except 1SF
Correct answer with no working scores 2
1(c)[2]
An answer that makes reference to two of the following
improvements and justifications
place a lid on the polystyrene cupIgnore just ‘better insulation’
and
to reduce heat loss
measure the temperature more oftenIgnore read the temperature for longer
and
Allow more accurate extrapolation / line of best fit
to give a more precise extrapolation (maximum
Ignore just to increase the accuracy
temperature change)
use a pipette / burette (to measure the solution)and
less uncertainty (in volume measurement)
Or
Allow to measure the temperature with more
use a thermometer with more gradations / more
precision (i.e with no mention of thermometer).
precise thermometer
Allow use a digital thermometer
and
to give a more precise temperature change
Ignore finer zinc powder
Ignore use a larger mass / excess of zinc
Ignore more concentrated solution
If no other mark scored award 1 for two correct
improvements of the four given
Do not award repeating the experiment
Do not award more accurate weighing
(Total for Question 1 = 13 marks)
Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.

