Note AcademyNote Academy

Chemistry (AS & A Level) · May / June 2026 · Paper 51 · Question 2

9701

As printed in the paper

The question as text

Ozone, O3(g), is a pollutant at ground level. Some experiments are done to determine the concentration of O3(g) in the air outside a school at different times of day. The method involves bubbling a sample of air through a solution of acidified iodide ions, Ž–(aq). Any O3(g) in the sample of air reacts to form triiodide ions, Ž3 –(aq). O3(g) + 3Ž–(aq) + 2H+(aq) Ž3 –(aq) + O2(g) + H2O(l) When starch solution is added to the mixture, it forms a coloured complex with Ž3 –(aq) ions. The concentration of Ž3 –(aq) is found by colorimetry and the percentage of O3(g) in the air is determined. A diagram of the colorimeter used is shown in Figure 2.1. 10 cm3 measuring cylinder 10 cm3 solution black box LED (light-emitting diode) photocell Figure 2.1 In the colorimeter, light from the LED passes through the solution in the measuring cylinder. Some of the light is absorbed by the complex containing starch and Ž3 – ions. The photocell is used to determine the absorbance of the solution in the measuring cylinder.

Read automatically from the paper; the printed page above is exact.

Show the answer and mark scheme
  • 2(a)[1]

    only (direct) light from the LED should be allowed to reach the photocell 1 A to prevent outside light entering (the colorimeter) A to prevent outside light reaching the photocell for outside light A external light / background light /surrounding light for photocell A detector A no (indirect) light via reflections A the only source of light is from the LED I other light for outside light I light absorbed unless it is absorbed by the photocell

  • 2(b)(i)[1]

    concentration of I3–(aq) / mol dm–3 resistance of photocell, Rs / kΩ absorbance, A 3.60 × 10-6 34.28 0.839 2.94 × 10-6 23.42 0.684 2.20 × 10-6 16.01 0.519 1.52 × 10-6 9.68 0.300 7.90 × 10-7 7.50 0.189 1 Must be 3 DP

  • 2(b)(ii)[1]

    distilled water (with few drops of starch solution) 1 A (acidified) I–(aq)/solution (with few drops of starch solution) A acidified I– ions (with few drops of starch solution) A I3– solution/(aq) with no starch

  • 2(b)(iii)[1]

    concentration of I3–

  • 2(b)(iv)[2]

    M1 all 5 points plotted correctly M2 straight line of best fit through origin passing through or close to all points except anomaly (point 2) 2 Place plotting tick on grid above line of best fit. Place line tick in left-hand margin Place a cross beside an incorrect point ecf from 2 (b) (i) R if point 2 is on a vertical gridline R if point 4 is on a horizontal gridline R line of best fit that does not extend from the origin to cover all plotted points. R if line of best fit is one square or more from origin on either axis A line of best fit between the first and last (correctly plotted) points is acceptable as long as it goes close enough to the origin. All points except anomaly should be on the line of best fit. Point marked as anomalous (ringed) should not be used in determining the line of best fit. A ecf acceptable line of best fit drawn for incorrectly plotted points. R line of best fit if the points (except anomaly) not approximately evenly distributed on both sides of line I extra points added which are used in later calculations I remnants of lines that the candidate has tried to erase R curved line R double or “sketchy” lines.

  • 2(b)(v)[1]

    most anomalous point circled AND any one reason from:

    not enough starch added (in step 2)
    less than 10.0 cm3 solution transferred (from boiling tube to measuring cylinder in step 4)
    solution (from step 2) was left for less than 10 minutes (in step 3) 1 Expected answer is point 2 at (1.52 × 10–6, 0.300 below the line of best fit) A light intensity (in colorimeter) increased A ora for ecf point above line of best fit A light got into the colorimeter/black box not shut (no ora for point above line of best fit) I reading of absorbance was too low I comments about temperature/heat I starch not mixed properly I systematic error I evaporation I reference to rates
  • 2(c)(i)[1]

    to allow all the I3– ions form a complex (with the starch) 1 A for complete reaction (of the I3– ions and starch) A enough time for the complex to form completely I to reach equilibrium I reference to rate of reaction I all the starch reacts

  • 2(c)(ii)[1]

    10 cm3 volumetric pipette 1 A graduated pipette as long as volume is not < 10 cm3 A 10 cm3 pipette A volumetric pipette I ‘pipette’ alone R burette

  • 2(c)(iii)[2]

    M1 absorbance = 0.640 M2 concentration read from the graph to nearest ±½ square and given to 3 SF 2 A 0.64 with working shown Concentration should be read from the graph to nearest ±½ square. I any figures after 3SF I trailing zeros (allow 2.7 for 2.70) A non-standard form 2.75 × 10–6 mol dm–3 is a common answer

  • 2(c)(iv)[1]

  • 2(c)(v)[1]

  • 2(c)(vi)[1]

    increases AND (the value of) the concentration of I3– increases (at same absorbance)

  • 2(c)(vii)[2]

    9.87 + 0.14 × 9.87 = 11.25 AND 13.66 – 0.14 × 13.66 = 11.75 AND the concentration of O3 is different (because the extremes of the ranges do not overlap) 1 A any set of calculations which gives 11.25 and 11.75

  • 2(c)(ix)[1]

    concentration of I3– will be higher giving a lower percentage error 1 A amount / mol of I3– for concentration of I3– I uncertainty for percentage error A uncertainty percentage error for percentage error alone

Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.