Note AcademyNote Academy

Physics · May / June 2025 · Paper 61 · Question 4

YPH11

As printed in the paper

The question as text

4 A student investigated the properties of a spring using the apparatus shown. spring stand mass

Read automatically from the paper; the printed page above is exact.

Show the answer and mark scheme
  • 4(a)(i)[3]

    An explanation that makes reference to the following points:

    The measurement (of time) will be larger

    Do not accept time period or T will be larger (for MP1 only).

    But the uncertainty will be constant

    So the percentage uncertainty will be reduced

  • 4(a)(ii)[2]

    Use a (timing) marker at the centre of the oscillation

    Start timing after several oscillations

    Or Use a small initial displacement

  • 4(a)(iii)[2]

    Example of calculation

    Mean value of 10𝑇𝑇=

    =

    (6.88 + 6.93 + 6.84 + 6.96) s

    27.61 s

    Calculates mean time (period) using all values

    4

    4

    [mean must be in data range]

    = 6.90 s

    Mean value of T = 0.69 s given to 2 d.p. only

    Mean value of T = 6.90 s / 10 = 0.69 s

  • 4(a)(iv)[2]

    Example of calculation

    (6.96 − 6.84) s

    Uses half range

    2

    Or Uses furthest from the mean

    Half range =

    = 0.06 s

    [Values consistent with those used to calculate mean]

    0.06 s

    6.90 s × 100 = 0.87 % = 0.9%

    Percentage uncertainty =

    Percentage uncertainty = 0.9%

    given to 1 or 2 s.f.

    e.c.f. (a)(iii)

    Use of full range scores 0

  • 4(b)(i)[2]

    An explanation that makes reference to the following points:

    ONE mark only for “repeat and calculate a mean to reduce (the

    EITHER

    effect of) random errors”

    Repeat at different orientations (at each end of the spring) and

    calculate a mean

    To reduce (the effect of) random error

    Do not allow eliminate/avoid. MP2 dependent on MP1

    OR

    ONE mark only for “check for zero error to eliminate

    systematic error”

    Check and correct for zero error

    Do not allow system/systemic. MP2 dependent on MP1

    To eliminate/reduce systematic error

  • 4(b)(ii)[3]

    Example of calculation

    59.4 mm × 100 = 0.34%

    EITHER

    0.2 mm

    Accept ∆𝐷𝐷

    𝐷𝐷 and ∆𝑑𝑑

    %U in D =

    𝑑𝑑

    13.9 mm × 100 = 0.72%

    Uses %U in D and %U in d

    0.1 mm

    Uses 2 × %U in D and 2 × %U d Accept 2 × ∆𝐷𝐷

    𝐷𝐷 and 2 × ∆𝑑𝑑

    %U in d =

    𝑑𝑑

    𝐷𝐷2

    2𝑑𝑑2

    %U in

    = 2 × %U in D + 2 × %U in d

    %U = 2.1(%) given to minimum 2 s.f.

    = 2 × 0.34% + 2 × 0.72% = 2.1 %

    OR

    𝐷𝐷2

    Example of calculation

    2𝑑𝑑2 =

    𝐷𝐷2

    (59.4 mm)2

    2𝑑𝑑2

    Uses uncertainties to calculate maximum or minimum in

    2 × (13.9 mm)2 = 9.13

    [Accept max/max or min/min]

    2𝑑𝑑2 =

    𝐷𝐷2

    (59.4 mm + 0.2 mm)2

    Uses half range from calculated maximum and minimum

    2 × (13.9 mm − 0.1 mm)2 = 9.326

    Maximum

    values

    2𝑑𝑑2 =

    𝐷𝐷2

    (59.4 mm − 0.2 mm)2

    [Accept max/max or min/min]

    2 × (13.9 mm + 0.1 mm)2 = 8.940

    Minimum

    %U = 2.1(%) given to minimum 2 s.f.

    𝐷𝐷2

    9.326 − 8.940

    2𝑑𝑑2 =

    2 × 9.13 × 100 = 2.1 %

    %U in

    [Only credit if both maximum and minimum are correct

    and half range calculated]

  • 4(b)(iii)[2]

    An explanation that makes reference to the following points:

    EITHER

    Example of calculation

    Lower limit of ν = 0.259

    The lower limit is below the value of 0.265 so the spring could

    Lower limit of ν = 0.276 × (1 − 0.06) = 0.259

    be made from steel

    Must see number being compared to.

    Or valid conclusion comparing limit with 0.265

    OR

    Example of calculation

    %D = 4 % using 0.265 as denominator

    0.276 − 0.265

    0.265

    As 4 % is less than 6% so the spring could be made from steel

    %D =

    × 100 = 4.2 %

    Or valid conclusion comparing %D with 6%

    Must see number being compared to.

    (Total for Question 4 = 16 marks)

    TOTAL FOR PAPER = 50 MARKS

    Pearson Education Limited. Registered company number 872828

    with its registered office at 80 Strand, London, WC2R 0RL, United Kingdom

Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.