Note AcademyNote Academy

Physics · Oct / Nov 2021 · Paper 61 · Question 4

YPH11

As printed in the paper

The question as text

4 An L-shaped steel rod was held horizontally in a stand clamped by its shorter end as shown. metre rule steel rod Diagram not to scale stand p q bench The end of the steel rod was at a height p above the bench. A student attached a mass m to the end of the steel rod causing it to bend towards the bench. The end of the steel rod was then at a height q above the bench.

Read automatically from the paper; the printed page above is exact.

Show the answer and mark scheme
  • 4(a)(i)[2]

    Any TWO from:

    Ensure the metre rule is vertical using a set square

    Accept alternative

    valid methods

    Ensure the end of the rod is close to the metre rule

    Or use a set square to read off the values

    Take readings perpendicular to the scale (to avoid parallax)

  • 4(a)(ii)[2]

    The uncertainty of a single reading is half the resolution of the metre rule,

    (which is 0.5 mm)

    As the two readings are subtracted, the uncertainties are added

  • 4(b)(i)[2]

    Micrometer screw gauge (with a resolution of 0.01mm) (Accept digital

    caliper)

    As this would produce an uncertainty of 0.25% which is small

  • 4(b)(ii)[2]

    One PAIR from:

    Repeat at different orientations and calculate a mean

    To reduce the effect of random errors

    Check (and correct) for zero error

    To eliminate systematic error

  • 4(b)(iii)[2]

    Mean value of d = 2.35 (mm)

    Calculation from half range shown to give uncertainty of 0.02 (mm)

    Example of calculation

    Mean d = (2.35 + 2.37 + 2.34 + 2.34 + 2.33) mm / 5 = 11.74 mm / 5

    = 2.348 mm = 2.35 mm

    Uncertainty = (2.37 − 2.33) mm /2 = 0.04 mm/2 = 0.02 mm

  • 4(c)[2]

    Use of G = (32mglx2) / (π yd 4) shown

    Correct value of G given to 2 or 3 s.f.

    e.c.f. (b)(iii)

    Bald answer scores 0

    Accept value of 1.5 × 1011 (N m−2) if d = 2 mm used

    Example of calculation

    G

    = 32 × 0.1kg × 9.81 N kg−1 × 0.589 m × (0.103 m)2

    3.14159 × 0.026 m × (2.35 × 10−3 m)4

    = 0.196 N m3 / 2.49 × 10−12 m5

    = 7.87 × 1010 (N m−2)

    = 7.9 × 1010 (N m−2)

    Calculation of correct value of %U in G

    e.c.f. (b)(iii)

    Correct value of relevant limits from %U

    e.c.f. (c)

    Valid conclusion based on comparison of relevant limits with data

    Example of calculation

    %U

    = (0.1 / 58.9) × 100 + 2 × (0.1 / 10.3) × 100 + (1 / 26) × 100

    + 4 × (0.02 / 2.35) × 100

    = 0.17% + 2 × 0.97% + 3.85% + 4 × 0.85%

    = 0.17% + 1.94% + 3.85% + 3.40%

    = 9.36% = 9.4%

    Upper limit = 78.7 × 109 N m2 × (1+0.094) = 86.1 × 109 N m2

    Lower limit = 78.7 × 109 N m2 × (1 − 0.094) = 71.3 × 109 N m2

    As both values fall within this range, the student cannot determine which type of

    steel the rod is made from.

    Or

    Use of uncertainties to calculate maximum or minimum shown

    Calculation of correct value of upper limit

    Calculation of correct value of lower limit

    Valid conclusion based on comparison of relevant limit with data

    Example of calculation

    Upper limit G = 32 × 0.1kg × 9.81Nkg−1 × (0.589+0.001)m × ((0.103+0.001)m)2

    3.14159 × (0.026−0.01) m × ((2.35−0.02) × 10−3 m)4

    = 0.200 N m3 / 2.31 × 10−12 m5

    = 8.68 × 1010 (N m−2)

    Lower limit G = 32 × 0.1kg × 9.81Nkg−1 × (0.589−0.001)m × ((0.103−0.001)m)2

    3.14159 × (0.026+0.01) m × ((2.35+0.02) × 10−3 m)4

    = 0.192 N m3 / 2.68 × 10−12 m5

    = 7.16 × 1010 (N m−2)

    As both values fall within this range, the student cannot determine which type of

    steel the rod is made from.

    Or

    Use of 2× %U in x Or 4× %U in d shown

    Calculation of correct value of %U in G

    e.c.f. (b)(iii)

    Correct calculation of relevant %D shown

    e.c.f. (c)

    Valid conclusion based on comparison of relevant %D with %U

    Example of calculation

    %U

    = (0.1 / 58.9) × 100 + 2 × (0.1 / 10.3) × 100 + (1 / 26) × 100

    + 4 × (0.02 / 2.35) × 100

    = 0.17% + 1.94% + 3.85% + 3.40%

    = 9.36% = 9.4%

    %D for structural steel = (78.7 − 79.3)/79.3 × 100 = 0.76 %

    %D for carbon steel = (78.7 − 77)/77 × 100 = 2.3%

    As % D for both structural and carbon steel are less than the %U, the student

    cannot determine which type of steel the rod is made from.

    Pearson Education Limited. Registered company number 872828

    with its registered office at 80 Strand, London, WC2R 0RL, United Kingdom

  • 4(d)[4]

    Any TWO from:

    Ensure the metre rule is vertical using a set square

    Accept alternative

    valid methods

    Ensure the end of the rod is close to the metre rule

    Or use a set square to read off the values

    Take readings perpendicular to the scale (to avoid parallax)

    The uncertainty of a single reading is half the resolution of the metre rule,

    (which is 0.5 mm)

    As the two readings are subtracted, the uncertainties are added

    Micrometer screw gauge (with a resolution of 0.01mm) (Accept digital

    caliper)

    As this would produce an uncertainty of 0.25% which is small

    One PAIR from:

    Repeat at different orientations and calculate a mean

    To reduce the effect of random errors

    Check (and correct) for zero error

    To eliminate systematic error

    Mean value of d = 2.35 (mm)

    Calculation from half range shown to give uncertainty of 0.02 (mm)

    Example of calculation

    Mean d = (2.35 + 2.37 + 2.34 + 2.34 + 2.33) mm / 5 = 11.74 mm / 5

    = 2.348 mm = 2.35 mm

    Uncertainty = (2.37 − 2.33) mm /2 = 0.04 mm/2 = 0.02 mm

    Use of G = (32mglx2) / (π yd 4) shown

    Correct value of G given to 2 or 3 s.f.

    e.c.f. (b)(iii)

    Bald answer scores 0

    Accept value of 1.5 × 1011 (N m−2) if d = 2 mm used

    Example of calculation

    G

    = 32 × 0.1kg × 9.81 N kg−1 × 0.589 m × (0.103 m)2

    3.14159 × 0.026 m × (2.35 × 10−3 m)4

    = 0.196 N m3 / 2.49 × 10−12 m5

    = 7.87 × 1010 (N m−2)

    = 7.9 × 1010 (N m−2)

    Calculation of correct value of %U in G

    e.c.f. (b)(iii)

    Correct value of relevant limits from %U

    e.c.f. (c)

    Valid conclusion based on comparison of relevant limits with data

    Example of calculation

    %U

    = (0.1 / 58.9) × 100 + 2 × (0.1 / 10.3) × 100 + (1 / 26) × 100

    + 4 × (0.02 / 2.35) × 100

    = 0.17% + 2 × 0.97% + 3.85% + 4 × 0.85%

    = 0.17% + 1.94% + 3.85% + 3.40%

    = 9.36% = 9.4%

    Upper limit = 78.7 × 109 N m2 × (1+0.094) = 86.1 × 109 N m2

    Lower limit = 78.7 × 109 N m2 × (1 − 0.094) = 71.3 × 109 N m2

    As both values fall within this range, the student cannot determine which type of

    steel the rod is made from.

    Or

    Use of uncertainties to calculate maximum or minimum shown

    Calculation of correct value of upper limit

    Calculation of correct value of lower limit

    Valid conclusion based on comparison of relevant limit with data

    Example of calculation

    Upper limit G = 32 × 0.1kg × 9.81Nkg−1 × (0.589+0.001)m × ((0.103+0.001)m)2

    3.14159 × (0.026−0.01) m × ((2.35−0.02) × 10−3 m)4

    = 0.200 N m3 / 2.31 × 10−12 m5

    = 8.68 × 1010 (N m−2)

    Lower limit G = 32 × 0.1kg × 9.81Nkg−1 × (0.589−0.001)m × ((0.103−0.001)m)2

    3.14159 × (0.026+0.01) m × ((2.35+0.02) × 10−3 m)4

    = 0.192 N m3 / 2.68 × 10−12 m5

    = 7.16 × 1010 (N m−2)

    As both values fall within this range, the student cannot determine which type of

    steel the rod is made from.

    Or

    Use of 2× %U in x Or 4× %U in d shown

    Calculation of correct value of %U in G

    e.c.f. (b)(iii)

    Correct calculation of relevant %D shown

    e.c.f. (c)

    Valid conclusion based on comparison of relevant %D with %U

    Example of calculation

    %U

    = (0.1 / 58.9) × 100 + 2 × (0.1 / 10.3) × 100 + (1 / 26) × 100

    + 4 × (0.02 / 2.35) × 100

    = 0.17% + 1.94% + 3.85% + 3.40%

    = 9.36% = 9.4%

    %D for structural steel = (78.7 − 79.3)/79.3 × 100 = 0.76 %

    %D for carbon steel = (78.7 − 77)/77 × 100 = 2.3%

    As % D for both structural and carbon steel are less than the %U, the student

    cannot determine which type of steel the rod is made from.

    Pearson Education Limited. Registered company number 872828

    with its registered office at 80 Strand, London, WC2R 0RL, United Kingdom

Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.