Note AcademyNote Academy

Chemistry · May / June 2024 · Paper 31 · Question 4

YCH11

As printed in the paper

The question as text

4 An experiment was carried out to determine the enthalpy change of neutralisation for the reaction between sulfuric acid and sodium hydroxide. H2SO4(aq) + 2NaOH(aq) → Na2SO4(aq) + 2H2O(l) Procedure Step 1 25.0 cm3 of 1.25 mol dm–3 sulfuric acid was placed in a polystyrene cup. The polystyrene cup was then placed in a beaker. A thermometer was used to measure the temperature of the acid and a clock was started. Step 2 The temperature of the sulfuric acid was measured every 30 seconds for 2½ minutes. Step 3 50.0 cm3 of 1.25 mol dm–3 sodium hydroxide solution was added to the acid in the polystyrene cup at 3 minutes and the mixture was constantly stirred. Step 4 The temperature of the mixture in the polystyrene cup was measured at 3½ minutes and then every 30 seconds until the clock reached 10 minutes.

Read automatically from the paper; the printed page above is exact.

Show the answer and mark scheme
  • 4(a)[1]

    An answer that makes reference to the following point:

    Accept descriptions

    to prevent the polystyrene cup from ‘falling over’

    Allow to stabilise the polystyrene cup

    Allow to prevent spillages

    Ignore references to heat loss

  • 4(b)[1]

    An answer that makes reference to the following point:

    to determine a consistent/steady/constant temperature

    Allow for determine a mean initial temperature

    (before adding the sodium hydroxide)

    Allow reference to achieve room temperature

    Ignore just to have a more accurate temperature

    Do not award references to the temperature cooling

    since this implies the effect after the reaction

  • 4(c)[2]

    An explanation that makes reference to the following points:

    Allow the temperature was not uniform/the same

    the temperature will be changing

    throughout the mixture

    Allow the temperature is still rising

    Ignore just the temperature will be inaccurate

    Allow because that’s when the sodium hydroxide

    because it takes time to add 50 cm3 of sodium hydroxide

    was added

    Allow because you cannot add the alkali and

    measure the temperature at the same time (1)

    Ignore references to the reaction ‘just’ starting or

    hasn’t finished

    If no other mark awarded, allow (1) for the

    thermometer was used for stirring/ the mixture was

    being stirred

  • 4(d)(i)[2]

    Example of working on graph:

    best fit line extrapolated to 3 minutes shown on the graph

    Ignore longer extrapolated lines

    Ignore vertical line not at 3 minutes for M1

    ∆T= (35 − 23=) 12 °C

    maximum temperature change

    M2 dependent on the temperature change being

    measured at 3 mins

    Allow ±1 for the highest temperature so range for

    ∆T=11 – 13 °C

  • 4(d)(ii)[2]

    An explanation that makes reference to the following points:

    there is no more reaction occurring

    Accept no more energy being released

    Allow the reaction is complete/

    all the acid reacted /all the NaOH has reacted

    Ignore the reaction is slowing down

    and heat is being lost (to the surroundings)

    Ignore just the mixture cools down

  • 4(d)(iii)[1]

    An answer that makes reference to the following point:

    the thermometer is not sufficiently precise/

    Allow the thermometer only measures ±1°C

    thermometer resolution insufficient (to show the change)

    Allow the thermometer is not sufficiently accurate

    Ignore references to incorrect reading of the

    thermometer

  • 4(d)(iv)[1]

    An answer that makes reference to the following point:

    the (starting) temperature is below 25 °C / 298K

    Allow standard temperature is not 23 °C / 296K

    Allow the temperature is not 25 °C / 298K

    Allow the temperature is lower than/not standard

    temperature

    Ignore just nonstandard conditions

    Ignore references to pressure

    Ignore references to the number of moles of water

    formed

  • 4(e)(i)[2]

    An explanation that makes reference to the following points:

    M2 dependent on award of M1 for both options

    Ignore any references to densities

    Either

    the specific heat capacity of acid/alkali is different from

    water/

    there is salt/sodium sulfate (dissolved) so the specific heat

    capacity is different

    so the assumption is not valid

    Or

    Allow the acid and alkali/reactants are aqueous

    ‘most’ of the acid and alkali solutions are water

    Ignore references to water as a product

    so the assumption is valid
  • 4(e)(ii)[1]

    An answer that makes reference to the following point:

    (neutralisation is per mol of water and) the number of

    Allow reference to dividing the number of moles of

    sulfuric acid by two

    moles of sodium hydroxide is the same as that of water

    Allow reference to dividing the answer by two

    Ignore reference to sodium hydroxide/sulfuric acid

    being the limiting reagent

    (Total for Question 4 = 13 marks)

    TOTAL FOR PAPER = 50 MARKS

    Pearson Education Limited. Registered company number 872828

    with its registered office at 80 Strand, London, WC2R 0RL, United Kingdom

Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.