Note AcademyNote Academy

Chemistry · May / June 2023 · Paper 21 · Question 20

YCH11

As printed in the paper

The question as text

20 This question is about fuels. The enthalpy change of combustion is the maximum amount of heat energy that can be obtained by the complete combustion of a substance. Values for the enthalpy change of combustion may be obtained by direct measurement or from mean bond enthalpies. These data may be used to assess the efficiency of fuels. Petrol is a mixture of a large number of different hydrocarbons containing between four and twelve carbon atoms. Octane, C8H18 , is a typical component of petrol.

Read automatically from the paper; the printed page above is exact.

Show the answer and mark scheme
  • 20(a)(i)[4]

    Here and throughout the paper

    Do not penalise correct premature rounding

    Penalise incorrect rounding only in their final answer

    Example of calculation

    identification and number of bonds broken

    Bonds broken:

    7 × C─C + 18 × C─H + 12.5 × O=O

    and

    the values needed (1)

    E (bond breaking) = 7 × 347 + 18 × 413 + 12.5 × 498

    = (+)16088 (kJ mol−1)

    evaluation of energy required (1)

    TE only if at least 2 bonds used

    Bonds formed:

    identification of bonds formed

    E (bond forming) = 16 × C=O + 18 × O─H

    and

    the values needed

    = 16 × 805 + 18 × 464

    and

    evaluation of energy produced (1)

    = (−)21232 (kJ mol−1)

    evaluation of enthalpy change of combustion (1)

    ΔcH = 16088 – 21232 = −5144 (kJ mol−1)

    TE at each stage (even if final value is positive)

    Ignore SF except 1 SF

    Units are not required but if given must be correct for

    the final value

    Correct answer with some working scores (4)

    An answer that makes reference to the following

  • 20(a)(ii)[2]

    Allow just bond enthalpies are average values

    the bond enthalpies are averaged over a (large) number of

    compounds (1)

    bond enthalpies always refer to substances in the gas phase

    Allow just octane is a liquid or water is a liquid

    and

    Allow calculations using mean bond enthalpies do not

    include changes of state

    octane and water are liquids when the value of ΔcHo is

    obtained (1)

    Ignore nonstandard conditions

    Do not award explanations for experimental error such

    as heat loss, or incomplete combustion

  • 20(a)(iii)[2]

    Example of calculation

    M = 8 × 12 + 18 = 114 g mol−1

    calculation of molar mass of octane (1)

    Allow mol octane = 1000÷(8x12 + 18x1) = 8.772

    Ignore just (8x12 + 18x1)

    conversion of kJ mol−1 to MJ kg−1

    1000 × 5470 ÷ 114 = 47982 kJ kg−1= 47.982 MJkg−1

    and

    calculation of percentage efficiency (1)

    Efficiency = 100 x 11 ÷ 47.982 = 22.925 /22.9 / 23%

    Allow conversion of MJ kg−1 to kJ mol−1

    = 114 x 11 x 1000 ÷ 1000 = 1254 (kJ mol−1)

    and

    Efficiency = 100 x 1254 ÷ 5470 = 22.925 /22.9 / 23%

    Ignore SF except 1 SF

    TE unless % efficiency > 100

    Correct answer with no working scores (2)

    Allow calculation using ΔcHo from mean bond

    enthalpy data (−5144 kJ mol−1):

    Efficiency =24.378%

    Allow calculation using stated incorrect ΔcHo from

    mean bond enthalpy data unless % efficiency > 100

  • 20(a)(iv)[2]

    An answer that makes reference to two of the following

    heat loss to the surroundings (1)

    Accept specific examples such as

    Heat loss due to friction in the engine

    Heat loss via hot exhaust

    Allow just ‘converted to heat’

    Allow energy loss to the surroundings

    Ignore just ‘friction’

    Allow energy is used to warm up the engine

    energy is used to bring the engine to operating

    temperature (1)

    Allow energy is used to start the engine

    Allow energy is used for aircon / electronic devices

    incomplete combustion (of the fuel) (1)

    Allow combustion is not smooth

    Ignore inefficient combustion

    Ignore references to standard conditions

    Ignore fuel evaporates

    Ignore petrol not 100% octane

    Ignore the idea that some other force is moving the car

    e.g. car is going downhill

    This question assesses the student’s ability to show a coherent and

    Guidance on how the mark scheme should be applied.

  • 20(b)[6]

    logically structured answer with linkages and fully sustained

    reasoning.

    The mark for indicative content should be added to the

    mark for lines of reasoning. For example, a response

    Marks are awarded for indicative content and for how the answer is

    with five indicative marking points that is partially

    structured and shows lines of reasoning.

    structured with some linkages and lines of reasoning

    scores 4 marks (3 marks for indicative content and 1

    The following table shows how the marks should be awarded for

    mark for partial structure and some linkages and lines of

    indicative content.

    reasoning).

    Number of indicative marking

    Number of marks awarded for

    If there were no linkages between the points, then the

    points seen in answer

    indicative marking points

    same indicative marking points would yield an overall

    6

    4

    score of 3 marks (3 marks for indicative content and no

    54

    3

    marks for linkages).

    32

    2

    1

    1

    In general it would be expected that

    0

    0

    5 or 6 indicative points would get 2 reasoning marks

    3 or 4 indicative points would get 1 reasoning mark

    The following table shows how the marks should be awarded for

    0, 1 or 2 indicative points would get 0 reasoning marks.

    structure and lines of reasoning

    Number of marks awarded

    If there is any incorrect chemistry, deduct mark(s) from

    for structure of answer and

    the reasoning. If no reasoning mark(s) awarded do not

    sustained lines of reasoning

    deduct mark(s).

    Answer shows a coherent logical

    structure with linkages and fully

    Comment: Look for the indicative marking points first,

    2

    sustained lines of reasoning

    then consider the mark for the structure of the answer

    demonstrated throughout

    and sustained line of reasoning

    Answer is partially structured

    with some linkages and lines of

    1

    reasoning

    Answer has no linkages between

    0

    points and is unstructured

    Indicative points

    *20(b)

    Similarities

    Allow van der Waals forces

    cont

    IP1both hydrogen and ammonia form London /

    Ignore permanent dipoledipole forces in ammonia

    dispersion forces

    Do not award H2 forms hydrogen bonds / permanent

    dipoledipole forces

    Accept fluctuating electron clouds result in differences in

    IP2 a temporary dipole forms in a molecule and induces a

    electron density within the molecule

    dipole in an adjacent molecule

    Allow instantaneous dipoledipole attractions between

    molecules

    IP3 the attraction (between the temporary dipoles) is small(er)

    Allow because H2 has only two / few electrons

    in hydrogen because the H2 electron cloud is not easily

    Allow attraction is greater in ammonia because it has

    polarised

    more electrons

    Differences

    Do not award ammonia forms hydrogen bonds with

    IP4 ammonia forms hydrogen bonds (because nitrogen is very

    water

    electronegative)

    IP4 and IP5 may be scored by a diagram showing dipole

    and lone pair and with H bond labelled

    δ+

    δ

    :

    Allow NH─N bond angle not equal to 180

    hydrogen bond

    IP5 Accept hydrogen bond forms between the nitrogen lone

    Allow hydrogen bond forms between the δ− nitrogen

    pair and the (δ+) hydrogen (of a different molecule)

    and the δ+ hydrogen (of a different molecule)

    IP6 ammonia liquefies more easily than hydrogen because

    Allow permanent dipoledipole forces for H bonds here

    hydrogen bonds are stronger than London forces

    Ignore just ‘Hbonding is the strongest IMF’

    Ignore reference to boiling temperatures

    Do not award hydrogen liquefies to form water

    Do not award energy is required to liquefy a gas

    (Total for Question 20 = 16 marks)

Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.