Chemistry · May / June 2022 · Paper 61 · Question 3
YCH11
As printed in the paper
The question as text
3 Brass is an alloy of copper. The percentage by mass of copper in a sample of brass can be determined by a three-stage process. Stage 1 Oxidation of the copper to copper(II) ions with excess concentrated nitric acid. Stage 2 Reduction of the copper(II) ions to copper(I) ions with excess iodide ions. Stage 3 Titration of the iodine produced in Stage 2 against a standard solution of sodium thiosulfate.
Read automatically from the paper; the printed page above is exact.
Show the answer and mark scheme
3(a)(i)[2]
An answer that makes reference to the following points:
Ignore irritant/harmful
Do not award any other reagent
e.g. sodium thiosulfate, iodine, brass
(concentrated) nitric acid is corrosiveAllow burns/blisters skin
and
Ignore toxic
Ignore avoid skin contact
wear/use gloves
Do not award nitric acid is flammable
nitrogen (di)oxide/NO2 (gas) is toxic/corrosiveand
Allow well ventilated room
Ignore reference to flames/bunsens/gas mask/face mask
carry out experiment in a fume cupboard
3(a)(ii)[2]
green solution formedAllow any shade of green/blue solution formed
Ignore metal would dissolve
(reddish/yellow) brown fumes formedIgnore just effervescence
3(a)(iii)[1]
An answer that makes reference to the following point:
to prevent too much effervescence/fizzing / theAllow the reaction is vigorous/
reaction mixture spilling over /CO2 being formed
to slow down the reaction
too quickly
Ignore exothermic (reaction)/water might boil/
splashing not linked to gas given off
Do not award to stop the reaction
3(a)(iv)[3]
A description that makes reference to three of the
If beaker/measuring cylinder used penalise in M1 only
following points:
If incorrect solvent e.g. ethanol/ethanoic acid used
penalise in M2 only
(transfer contents of beaker to) and washings to avolumetric flask
make up to the mark with (distilled/deionised)Allow standard / graduated flask
water
Allow any indication of mixing e.g. inverting/swirling
shake / mix3(b)(i)[2]
Example of calculation
adding electrode potentialsEcell = +0.15 − 0.54 = −0.39(V)
cell potential is negative/<0 (so not feasible)Incorrect negative Ecell value can score M2
3(b)(ii)[2]
the copper (I) iodide/Cu+ precipitates / is removedfrom the equilibrium / the concentration of
copper(I) in solution is very low
the equilibrium position moves to the righthandAccept the actual electrode potential (for Cu2+/ Cu+)
side
is higher/more positive than the standard electrode
potential
Ignore reference to activation energy / rate of
reaction/nonstandard temperature/pressure
Allow 1 mark for concentrations are nonstandard
If value in (i) for Ecell is positive then allow 1 mark
in (ii) for reference to a spontaneous reaction for a
positive Ecell
3(c)(i)[1]
an (insoluble) complex/solid will be formedAllow iodine binds to the starch and
makes the end point more difficult to see
3(c)(ii)[1]
blueblack to colourless (at the end point)Allow blue or black
Ignore clear
3(c)(iii)[1]
Example of calculation
calculation of titre and mean of concordant results(27.05;26.65) 26.45
(26.65 + 26.45) ÷ 2 = 26.55(cm3)
3(c)(iv)[3]
Example of calculation
26.55 × 0.095 = 2.52225 × 10−3 / 0.00252225 (mol)
calculation of moles thiosulfate in titre1000
TE on (c)(iii)
calculation of mass of copper in 25cm3 as2.52(225) × 10−3 × 63.5 = 0.160163 (g)
stoichiometry of Cu: thiosulfate is 1:1
0.160163 ×10 x 100 = 63.305/ 63.31/63.3/63 %
calculation of % of copper by mass in sample2.53
TE on M2 unless greater than 100 %
Ignore SF except 1 SF
Correct answer with some working scores (3)
3(c)(v)[2]
An explanation that makes reference to two of the following
points:
because more iodine will be producedmore thiosulfate will be needed (so the titre willbe greater) and the percentage of copper will be
greater
(Total for Question 3 = 20 marks)
Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.

