Note AcademyNote Academy

Chemistry · May / June 2022 · Paper 51 · Question 17

YCH11

As printed in the paper

The question as text

17 Gilding Metal Gilding metal is a type of brass alloy that consists of copper and a small amount of zinc, ranging from 5 % to 11 % by mass. Copper is very malleable and is hardened by the addition of zinc. Gilding metal is much less susceptible to cracking due to corrosion than brasses with a higher percentage of zinc. It has a warm, golden colour and can be used to coat materials using electrolysis. It is also used to make test pieces in jewellery manufacture because it has similar properties to silver but is less expensive. The proportions of copper and zinc determine the exact properties of the gilding metal and can be determined by chemical analysis.

Read automatically from the paper; the printed page above is exact.

Show the answer and mark scheme
  • 17(a)(i)[4]

    Example of calculation

    calculation of moles of CuSCN (1)

    4.69 ÷ 121.6 = 0.038569 / 3.8569 x 10–2 (mol)

    calculation of moles of Cu (1)

    1:1 so = 0.038569 / 3.8569 x 10–2 (mol)

    M2 can be subsumed as part of M3

    calculation of mass of Cu (1)

    0.038569 × 63.5 = 2.4491 (g)

    calculation of % of Cu

    (2.4491 ÷ 2.72) x 100 = 90.04 %

    and

    Ignore SF except 1 SF

    statement that it is a gilding metal (1)

    Allow TE at each step

    Note – if TE for M4 gives answer outside range

    of 9589 % then must be identified as NOT a

    Note – allow 121.5 for Mr of CuSCN in M1 but do not award

    64 for copper in M3

    gilding metal

    Do not award TE for M4 if answer > 100 %

    Allow calculation of % of Zn to show whether

    sample is a gilding metal

  • 17(a)(ii)[3]

    An explanation that makes reference to the following points:

    the Ecell data indicates that Cu2+ should not be reduced to Cu+

    Accept Ecell = −0.02 V

    and

    and

    Cu+ should be reduced to Cu (1)

    Ecell = +0.35 V

    Cu2+ can be reduced to Cu+ as the conditions must be nonstandard

    Allow addition of OH– ions as

    and

    alternative for conditions must be non

    as the Eo values are so close (1)

    standard

    but Cu+ is not reduced to Cu as the reaction must be kinetically

    hindered / have a high activation energy / very slow (1)

    Allow ‘not kinetically favoured’

  • 17(b)[4]

    white precipitate forms / precipitate of Zn(H2O)4(OH)2 forms (1)

    Accept sufficient NaOH will need to be

    added to neutralise the excess nitric acid

    Allow precipitate of Zn(OH)2 forms /

    precipitate of zinc hydroxide forms

    M1 can be awarded from correct

    formulae and state symbol in equation,

    hence fully correct equation with state

    symbol for solid scores M1 and M2

    Allow solid / crystals for ppt

    Zn(H2O)62+ + 2OH− → Zn(H2O)4(OH)2 + 2H2O (1)

    Allow Zn2+ + 2OH− → Zn(OH)2

    but as excess NaOH(aq) is added, precipitate will dissolve (1)
    due to formation of Zn(OH)42 (1)

    Correct formulae for M4 can be shown

    as part of an equation, even if equation is

    not correct

    Ignore state symbols even if incorrect

    Ignore omission of square brackets

    Ignore comments on validity of

    procedure

  • 17(c)[2]

    An explanation that makes reference to the following points:

    zinc ions disrupt layers / disrupt structure of copper

    Allow reference to atoms

    ions (1)

    zinc ions are a different size to copper ions / zinc

    ions are larger than copper ions

    Do not award M1 if particles referred to as

    molecules or forces referred to as intermolecular

    forces

    (so) layers (of copper ions) are less likely to slide over

    Allow ‘atoms are less likely to slide over each

    each other (1)

    other’

    Allow reverse argument

  • 17(d)(i)[3]

    A diagram that makes reference to the following points:

    two correctly labelled electrodes (1)
    both solutions and concentrations correct (1)

    Allow any soluble zinc and copper salts

    Allow name or formulae in M1 and M2

    salt bridge labelled, touching both solutions and

    If the solution for the salt bridge is discussed it must

    be correct

    voltmeter shown (1)

    Ignore temperature and pressure

    Example of diagram

  • 17(d)(ii)[3]

    Example of calculation

    calculation of E for zinc half cell / calculation of E

    0.34 – 1.09 = –0.75 (V)

    Eo (1)

    –0.75 = –0.76 + (0.0260/2) × ln[Zn2+]

    insert values in Nernst equation

    and

    ln[ion] = (0.01) x (2/0.026)

    rearrangement of Nernst equation (1)

    ln [ion] = 0.769230

    [ion] = 2.1581 (mol dm−3)

    calculation of [ion] (1)

    Ignore SF except 1SF

    Allow TE throughout

    Alternative Route

    0.34 – –0.76 = 1.10 (V)

    calculation of Eocell (1)

    1.10 = 1.09 + (0.0260/2) × ln[Zn2+]

    insert values in Nernst equation

    and

    ln[ion] = (0.01) x (2/0.026)

    rearrangement of Nernst equation (1)

    ln [ion] = 0.769230

    [ion] = 2.1581 (mol dm−3)

    calculation of [ion] (1)

    Ignore SF except 1SF

    Allow TE throughout

    (Total for Question 17 = 19 marks)

    (TOTAL FOR SECTION C = 19 MARKS)

    TOTAL FOR PAPER = 90 MARKS

    Pearson Education Limited. Registered company number 872828

    with its registered office at 80 Strand, London, WC2R 0RL, United Kingdom

Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.