Chemistry · May / June 2021 · Paper 31 · Question 4
YCH11
As printed in the paper
The question as text
4 A sample of 1-bromobutane may be prepared by reacting butan-1-ol with sodium bromide and 50 % concentrated sulfuric acid. C4H9OH + NaBr + H2SO4 → C4H9Br + NaHSO4 + H2O Procedure Step 1 Add suitable quantities of butan-1-ol and sodium bromide solution to a round-bottom flask. Place the flask in a cold water bath. Add concentrated sulfuric acid drop by drop to the flask. Step 2 Heat the mixture in the flask under reflux for about 45 minutes. Step 3 Rearrange the apparatus for distillation and distil the reaction mixture. The distillate collected contains 1-bromobutane and water in separate layers. Remove as much of the water layer as possible. Step 4 Transfer the impure 1-bromobutane to a separating funnel, add sodium hydrogencarbonate solution and shake the mixture. Run off the organic layer into a clean conical flask. Step 5 Add anhydrous calcium chloride, stopper the flask and allow it to stand. Decant the liquid. Step 6 Distil the product over a suitable temperature range to give pure 1-bromobutane. Data Property Butan-1-ol 1-Bromobutane Density / g cm−3 0.810 1.27 Molar mass / g mol−1 74 137 Boiling temperature / ° C 118 102
Read automatically from the paper; the printed page above is exact.
Show the answer and mark scheme
4(a)[2]
An answer that makes reference to the following points:
gives a reason for cooling
reaction is exothermic / vigorous / gives off heat
/
Do not award Explosive
Ignore violent / quick reaction
gives a reason why this causes a reduction in yield
mixture may boil causing reactant / product to
escape /
butan1ol /reactant or 1bromobutane /
product might evaporate
or
reaction may bubble / fizz / effervesce and
overflow the round bottom flask (causing loss
of reactant / product)
Allow alkene formation / charring
Ignore reference to equilibrium / rate / side
reactions
Do not award transfer losses
4(b)(i)[1]
Allow description of antibumping granules
antibumping granules
Allow other names:
antibumping chips / beads
boiling stones
broken porcelain
boiling chips
4(b)(ii)[3]
A diagram that
Example of diagram:
contains a round bottom flask with contents and
any indication of heating
water out
condenser
contains a vertical condenser with water jacket and
correct water flow
water in
is a working apparatus: not stoppered, no gaps, a
joint between flask and condenser
roundbottom
flask
Allow apparatus unlabelled but must have
correct water flow for M2
Allow pear shaped flask
Allow an arrow pointing upward as an indication
of heat
Ignore thermometers which do not seal the
apparatus
M1 is available for a distillation apparatus
4(c)(i)[1]
An answer that makes reference to the following points:
to neutralise (excess sulfuric) acid
Allow to remove (excess sulfuric) acid
Allow hydrobromic acid / HBr / sodium
hydrogensulfate / NaHSO4 / H+
Do not award just ‘to neutralise’ without
mention of acid
4(c)(ii)[2]
An explanation that makes reference to the following
points:
identifies the problem
buildup of pressure (in the separating funnel)
Ignore causes frothing
Ignore formation of CO2
gives a solution
open / remove the stopper (with the funnel
upright)
or
open the tap (with funnel inverted)
Note: Remove the stopper to release the
pressure would score 2.
Comment: mark independently
4(c)(iii)[1]
An answer that makes reference to the following points:
drying agent / to remove water
Do not award dehydration
4(c)(iv)[1]
An answer that makes reference to the following points:
Ignore colourless
turns from cloudy to clear
Allow solution becomes clear
Allow stops being cloudy
Allow is no longer turbid
Allow less cloudy / more clear
4(d)[1]
An answer that makes reference to the following points:
integer values of temperature in the ranges
Award values to nearest 0.5 oC
lower value 99 / 100 / 101(oC)
Do not award other fractions or decimals of
and
degrees other than nearest 0.5 oC
upper value 103 / 104 / 105(oC)
Do not award single values even if between the
two ends of the range, e.g. 102 oC
Allow a value for the size of the range around a
stated temperature as long as it is within the
given values e.g. 3 oC around 102 oC
4(e)(i)[1]
Example of reasons:
reason for yield being less than 100%
reaction incomplete
transfer losses
side reactions
Ignore equilibrium reached
Ignore impure reagents / impurities
Do not award the cold water bath was not used
Do not award the procedure was not followed
correctly
Do not award spillages
4(e)(ii)[4]
Example of calculation:
calculation of mass of 1bromobutane required
= 20 x 1.27 = 25.4 (g)
calculation of moles of 1bromobutane required
= 25.4 ÷ 137 = 0.18540 (mol)
calculation of mass butan1ol required
= 0.18540 x 74 = 13.720
calculation of percentage yield assumed
= 100 x 13.720 ÷ 21.0 = 65.332 (%)
OR
calculation of moles of butan1ol used
= 21 ÷ 74 = 0.28378 mol
calculation of mass of 1bromobutane for 100 % yield
= 0.28378 x 137 = 38.878 g
calculation of volume of 1bromobutane for 100 %
= 38.878 ÷ 1.27 = 30.613 (cm3)
yield
= 100 x 20 ÷ 30.613 = 65.332 (%)
calculation of % yield if 20 cm3 prepared
Do not award M4 if yield greater than 100%
Use of 0.810 instead of 1.27 gives 41.699 (%)
scores (3)
Use of transposed Mr values gives 223.9 (%)
scores (2)
Allow use of 136.9 (giving 65.381(%))
Allow TE throughout
Ignore SF except 1SF
Correct answer with some working scores (4)
(Total for Question 4 = 17 marks)
Total for Paper = 50 marks
Pearson Education Limited. Registered company number 872828
with its registered office at 80 Strand, London, WC2R 0RL, United Kingdom
Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.

