Note AcademyNote Academy

Biology · Oct / Nov 2021 · Paper 31 · Question 2

YBI11

As printed in the paper

The question as text

2 Scientists investigated the effect of salts on the permeability of cell membranes of beetroot. The diagram shows a beetroot cell with a vacuole containing the red pigment betalain. cell wall vacuole membrane (tonoplast) cell surface membrane cytoplasm betalain nucleus Equal sized discs of tissue were cut from a beetroot. Twenty of these discs were placed into a beaker containing a calcium chloride solution. This was repeated for several concentrations of calcium chloride and several concentrations of ammonium sulfate. Betalain leaked from the discs, changing the colour of the solutions in the beakers. The intensity of each colour was recorded after 12 hours.

Read automatically from the paper; the printed page above is exact.

Show the answer and mark scheme
  • 2(a)(i)[3]

    An explanation that includes the following points:

    because the same {light source / filter / size

    cuvette} used for all measurements (1)

    because zeroing / calibrating (1)

    described

    because objective measurement (1)
    because no light lost / gained (1)
  • 2(a)(ii)[2]

    An answer that includes the following points :

    temperature, use of thermostatically controlled

    accept room

    water bath / incubator (1)

    pH, use of buffer (1)
  • 2(b)(i)[3]

    Loss of betalain from beetroot

    A table showing the following

    cells / a.u.

    features:

    suitable table drawn (1)

    Concentration of

    with

    with calcium

    salt / mmol dm‐3

    ammonium

    chloride

    sulfate

    headings with units (1)

    0.00000

    0.30

    0.30

    all data correctly entered

    0.00025

    0.46

    0.29

    0.00200

    0.50

    0.15

    0.02000

    0.47

    0.02

    Allow

    0.00025 to 0.0003 second cell, first column

  • 2(b)(ii)[3]

    An answer including of the following points :

    Similarities

    both salts affect leakage (1)

    accept effect on

    permeability

    in both, greatest effect is over a small initial

    increase in salt concentration (1)

    Differences

    calcium chloride causes {leakage / intensity of

    for calcium chloride

    colour} to decrease, ammonium sulfate causes

    inverse,

    for ammonium sulfate

    {leakage / intensity of colour} to increase,

    direct relationship

    (with increase in concentration) (1)

    accept higher / lower

    loss for {Ammonium

    Sulfate / Calcium

    Chloride}

    a small initial change in ammonium sulfate

    concentration causes a larger change in leakage

    compared with a small initial change in calcium

    chloride concentration (1)

  • 2(b)(iii)[2]

    An answer including the following steps :

    allow ecf

    figures read off graph for CaCl2 (A) and

    e.g.

    (NH4)2SO4 (B), BA = C (1)

    {0.48 / 0.49} 0.09 =

    {0.39 / 0.40}

    accept anything

    between 0.48 and

    C ÷ A × 100 = D (%) (1)

    0.49

    0.39 ÷ 0.09 = 433 /

    433.3 / 433.33 (%)

    0.40 ÷ 0.09 = 444 /

    444.4 / 444.44 (%)

    OR

    0.39 ÷ 0.49 = 80 /

    79.6 / 79.59%

    0.40 ÷ 0.49 = 82 /

    81.6 / 81.63%

  • 2(c)(i)[3]

    An answer including the following points :

    with calcium chloride and ammonium sulfate

    the {leakage / permeability / intensity of

    colour} is more than with calcium chloride

    alone (1)

    with ammonium sulfate, leakage increased

    (compared with water) (1)

    accept increasing

    {pattern is the same in both lines in second

    calcium chloride

    experiment / described} (1)

    conc. leads to

    decrease in intensity

    of colour (etc) with or

    without ammonium

    sulfate

    accept correct figures

    at 0.010 mmol dm3 calcium chloride alone

    quoted

    {leakage / intensity of colour} is {equal / only

    slightly different} to that with ammonium

    sulfate with calcium chloride (1)

    calcium chloride can reverse the effects of

    ammonium sulfate (on membranes) (1)

  • 2(c)(ii)[3]

    An answer including the following points :

    repeat readings at 0.002 mmol dm3 (1)
    under same conditions (each time) (1)
    calculate (mean and) standard deviation (1)

    accept error bar

    accept ref to SD

    accept perform ttest

Make a free account to save your answers and see your weak topics and ask the AI why a wrong answer is wrong.